MGM Servizi Geologici
ITENG
Request a survey

MGM Servizi Geologici · Boreholes and drilling

Continuous-core geotechnical boreholes

With continuous coring we recover the entire soil column, metre by metre. We log it layer by layer, take the samples and store it in core boxes.

Tracked drill rig at work in an airport area, with an airliner in the background
Continuous-core borehole with the CMV MK 420D.

Geotechnical boreholes continuous coring

With continuous-core boreholes we extract the soil from ground level down to the required depth, place it in core boxes and reconstruct its stratigraphy.

The core diameter is 101 mm, with 126 mm casing. Depending on the ground we use single, double or triple core barrels; for environmental sampling we drill dry boreholes.

Our fleet covers every site condition: the CMV MK 420D for great depths and large diameters, the Mori M20 on rubber tracks, the modular Soil Sistem S350 HY for the tightest and lowest spaces, and a hand-held Hilti mini core drill for places that can only be reached on foot.

  • undisturbed and disturbed sampling for laboratory testing;
  • environmental sampling for chemical analysis;
  • definition of the site stratigraphy;
  • SPT tests in the borehole;
  • installation of piezometers and inclinometer casings.

SPT test Standard Penetration Test

The SPT is carried out at the bottom of a borehole by driving a standard sampler into the ground with a 63.5 kg hammer dropped from a height of 76 cm.

The blows needed for three successive 15 cm intervals are counted, for a total of 45 cm. The Raymond sampler has an outer diameter of 51 mm and a length of 813 mm.

Drill head with the SPT equipment, beside the water tank and the site van
SPT equipment on the drill rig.

Piezometers and inclinometers groundwater and movements

We install piezometers to measure the groundwater level and to take groundwater samples, and inclinometer casings to monitor ground movements at depth over time, for example on unstable slopes and near excavations and retaining structures.

Regular monitoring of the readings is the basis for foundation and excavation design, for hydrogeological and stability studies and for the characterisation of contaminated sites.

Red head of a newly installed piezometer in the ground, with a green area in the background
Piezometer installed at the end of a borehole.

The drill rigs

CMV tracked drill rig at work on a mountain site, with snow-covered peaks in the background

Tracked hydraulic drill rig

CMV MK 420D

The machine for high performance: continuous-core boreholes, micropiles and ground anchors, including large diameters, and inclined drilling.

Applicationscore drilling, micropiles, ground anchors, tie-backs, down-the-hole hammer, jet grouting
EngineDeutz diesel, 50 kW (68.5 hp)
Maximum rotary head torque4.78 kNm
Rotary head stroke1,800 mm
Thrust / pull-back26 kN / 38.5 kN
Clampsdiameter from 60 to 260 mm
Masttilting, for inclined drilling
Operating weight5,600 kg
Mori M20 drill rig at work on a slope among solar panels, with badlands in the background

Drill rig on rubber tracks

Mori M20

Agile and low-impact, suited to paved and delicate areas: boreholes and micropiles without damaging the surfaces.

Applicationsboreholes, micropiles, minipiles and ground anchors, even in hard-to-reach areas
Power55 kW (75 CV)
Weight3,900 kg
Pull force24 kN
Undercarriagerubber tracks
Soil Sistem S350 HY modular drill rig at work in a tiled indoor room

Modular drill rig

Soil Sistem S350 HY

It can be split into modules to reach the tightest and lowest spots: cellars, interiors, courtyards and narrow passages.

Power75 kW (100 CV)
Weight900 kg + 3,400 kg (two modules)
Pull force20 kN
Hilti core drill on its stand during coring at the base of a stone wall, with the operator beside it

Portable core drill

Hilti hand-held mini core drill

For coring in places that can only be reached on foot.

Where we work

Our office is in Ascoli Piceno: we work in the city and the province, in the Marche, Abruzzo and Lazio, and throughout Italy.

Our other services

Do you need boreholes for a project?

Tell us what you need and we will give you the COMPLETE solution.

+39 320 698 0036info@mgmgeologia.it